Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
The publisher is making a number of good observations related to How to Install a Bathtub in general in this article following next.
Installing a bathtub isn't precisely brain surgery, yet it does need solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably challenging project. If the old bathtub is readily accessible, the job can move rapidly; if you need to open up a wall to remove the old bathtub and also place the new bath tub, the job is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly require an assistant to move out the old bathtub and embeded in the new one. See to it you have certified on your own for the job and also are comfortable trying it. Instead of employing a contractor to take over a halfway-completed project, it is much better to consider employing one before you begin. Possibilities are you might need an expert plumber to make tube links.
This post will certainly assist you set up a new bathtub in your restroom if you have currently acquired a brand-new tub and do not need to change the setup of your previous water pipelines.
Your tools and also product checklist need to make up the following:
Planning for the Setup
Firstly, the sustaining framework provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to prevent stress on the bathtub.
Fit the versatile tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its final setting.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted accessibility that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wooden boards under its feet, position the tub in the called for position. The wood boards are useful in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub up until the level reviews degree.
To mount taps, fit the bottom of the furthest adaptable faucet port to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the supply of water and examine all joints as well as brand-new pipework for leaks and tighten them if needed. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub needs to wait up until the bath tub has been used a minimum of when as this will settle it into its last position.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin making sure that the washers remain in place between the tap and also the sink. Secure the tap in position with the maker supplied backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet ports. The previous type needs to be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to permeate the wall in between the bath and also the tiling, causing problems with wetness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and installations. They are sold in tubes as well as cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can break relatively early if you do not consider this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily readily available on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that blog posting on How to Install a Bathtub while doing a search on the web. Appreciated our blog entry? Please share it. Help other people find it. I cherish reading our article about Installing A Bathtub.
We've got solutions! Report this page